30" x 10' - 1440psig - Sour - 3 Phase - Dressed 2 Separator Package

30-11927 (2).jpg
30-11927 (3).jpg
30-11927 (4).jpg
30-11927 (5).jpg
30 - 40395 (2).jpg
30 - 40395 (3).jpg
30 - 40395 (4).jpg
30-11927 (1).jpg
30-11927 (2).jpg
30-11927 (3).jpg
30-11927 (4).jpg
30-11927 (5).jpg
30 - 40395 (2).jpg
30 - 40395 (3).jpg
30 - 40395 (4).jpg
30-11927 (1).jpg

30" x 10' - 1440psig - Sour - 3 Phase - Dressed 2 Separator Package

0.00

EVS-16025

30” X 10’0” 1440psi 3-Phase Sour Vertical Separator
MAWP 1440psi @ 130degF, MDMT -20degF @ 1440psi
Corrosion Allowance ⅛”, RT-1, PWHT, Sour service
ABSA Approved design registered in Ab, BC & Sask
Built and certified to ASME “U” stamp standard
3” 600# Inlet c/w 3” elbow diverter
3” 600# Gas out
2” 600# Drain connection
2 – 2” 600# Liquid outlets
2 – 3” 600# LC connections
2” 600# PSV connection
3” 600# HLSD connection
2 – 3” 600# Inspections
4 – 2” 600# LG connections
2” 600# PI connection
2” 600# TI connection
Internal float shield
6”x9#/cu.ft. Demister pad
Mercer 8100 1”mnpt x 1”fnpt “E” orifice PSV
WCB cs body & inlet base
Teflon seat, 316 ss disk & nozzle
Inconel x750 spring, sour gas service
Spring range 1226-1480psi
Set @ 1440psi
WIKA reflex sight glass w/ WIKA valves & ¾” isolation valves
WLG-20-17R-1CN – 9.13” visible area
WLG-110-1N gaugecocks
WGI ½”npt 0-1500psi dual scale, liquid filled, 4” pressure indicator
Inlet Piping and ESD Valve:
3” 600# RF flange at skid edge
Canalta 3” 600# dual chamber meter run – new
AGA 2000 Ed., A216 WCB, left hand
Orifice plate – 3” x 1/8”, 1.500, 316
Contour flow conditioner: Pin, 0.75 beta
WGI ½”npt 0-250degF dual scale, 3” temperature indicator w/ ¾”npt thermowell
2” 600# manual globe valve for back pressure control
3” 600# RF flange at skid edge
Liquid Process:
Norriseal 1001A pneumatic liquid level controller
Snap, direct acting
Norriseal 2220 2” level control valve
2” 600# RF body
1.00” Quick opening trim
ATO/Fail close
2nd phase liquid process, 2” 600# RF flange at skid edge
Vessel drain, 2” 600# RF flange at skid edge
Instrument Gas:
*Fuel gas source TBD
1”npt fuel gas manifold w/ ¼”npt needle valves
CVS controls regulator
¼”npt tapped-bonnet
0-35psi, adjustable spring range, 5 micron filter
WGI ¼”npt 0-160psi dual scale, liquid filled, 2.5” pressure indicator
Heater:
CCI 24” x 24” WX Series cata-dyne explosion proof heater
12 Volt start w/ 30’ cables
11” W.C. Nat gas thermocouple & ASV375 valve
CSA approved
Fisher 912 regulator, grill, vent hood, temp control and accessories
Support Skid:
8’0” x 10’0” Structural steel skid
W6 Main rails and vessel supports
C5 Floor supports
4 x Lift eyes
3/16” checker plate floor
3/8” Vessel base plate
2” Poly-urethane spray foam insulation under checker plate
Building:
8’ x 10’ x (10’6”-10’0”) H Shed style foam panel building
1.5” thick; 28Ga Polyurethane foam panels (R12); Galvalume (interior/exterior)
(1) 3’x7’ Foam panel door c/w panic hardware (Von Duprin – model 44TP) c/w locking cylinder
2’x2’ GPW, check-chain, door sweep, mohair weatherstripping & butt hinges
(1) 36”x36” Single glazed slider window c/w screen
(2) 12”x12” stamped aluminum vents c/w manual sliders
Valves:
3 – Fusion 2” 600# RF RP ball valve, cs body ss trim
2 – Frontier ¾”npt 2000# RP ball valve, cs body ss trim
2 – Frontier ½”npt 2000# RP ball valve, cs body ss trim
2 – MAS ½”npt FP 2000# ball valve, cs body ss trim
1 – WGI ½”npt MxF 10,000# needle valve, 316ss body & stem
3 – WGI ¼”npt MxF 10,000# needle valve, cs body & 316 ss stem

 

 

Quantity:
Add To Cart

New

East Central AB