36" x 10' - 1440psig - Sweet - 3 Phase - Dressed 2 Separator Package

coming soon.jpg
coming soon.jpg

36" x 10' - 1440psig - Sweet - 3 Phase - Dressed 2 Separator Package

0.00

EVS-16028

MAWP 1440psi @ 130degF, MDMT -20degF @ 1440psi
Corrosion Allowance 1/8”, RT-1, PWHT, Sour service
ABSA approved design and registered in Ab, BC, & Sask
Built and certified ASME “U” stamp standard
3” 600# Inlet c/w 3” elbow diverter
3” 600# Gas out connection
3” 600# Water out/bottom inspection
2” 600# Condensate out connection
2” 600# Drain connection
2 – 3” 600# LC connections
2” 600# PSV connection
3” 600# HLSD connection
3” 600# Inspection
4 – 2” 600# LG connections
2” 600# PI connection
Internal float shield
6”x9#/cu. Ft. Demister pad
Mercer 8100 1”mnpt x 1”fnpt “E” orifice PSV
WCB cs body & inlet base
Viton seat, 304 ss disk & 316 nozzle
Inconel x750 spring, gas service
Spring range 1226-1480psi
Set @ 1440psi
WIKA reflex sight glass w/ WIKA valves & ¾” isolation valves
WGI ½”npt 0-1500psi dual scale, liquid filled, 4” pressure indicator
Inlet Piping and Control Valve:
3” 600# RF flange at skid edge
CVS 2” 600# RF short body series D inlet control valve (note 2)
1” SST Micro-form trim
LCC body, NACE
CVS series 667-45 ATO/Fail close actuator
14-30psi Bench set
¾” Travel
CVS 4150 Pressure controller
6-30psi
Reverse acting
0-1500psi Bourdon tube, NACE
Proportional
Sales Gas Process:
Canalta 3” 600# dual chamber meter run – new
AGA 2000 Ed., A216 WCB, left hand
Contour flow conditioner: Pin, 0.75 beta
WGI ½”npt 0-250degF dual scale, 3” temperature indicator w/ ¾”npt thermowell
2” 600# Manual globe valve for back pressure control
3” 600# RF flange at skid edge
Liquid Process:
Norriseal 1001A pneumatic liquid level controller
2”npt, R.H. Mount
Snap, direct acting
Norriseal 2220 2” level control valve
2”npt body
1.00” Quick opening trim
ATO/Fail close
Jag T2-F20T09N Inlet ESD Valve
2”npt 2000# Full port ball valve
Floater, NACE/Std
CVS160SR-06 Pneumatic spring return actuator
40psi supply required
ATO/Fail closed
2nd phase liquid process, 2”npt at skid edge
Vessel drain, 2”npt at skid edge
Instrument Gas:
6” x 36” 285psi sweet scrubber w/ internal HLSD
Belgas 627 Pressure regulator
1”npt 627 body material: WCC steel
Spring case material: Aluminum
1/8” orifice SST nylon disk
Spring range 70-150 psig
Max inlet pressure: 2000 psig
Mercer 8100 1”mnpt x 1”fnpt “E” orifice PSV
WCB cs body & inlet base
Viton seat, 304 ss disk & 316 nozzle
Inconel x750 spring, gas service
Spring range 86-190psi
Set @ 150psi
557 SCFM Air
½”npt fuel gas manifold w/ ¼”npt needle valves
(2) Belgas P50 regulator
¼”npt tapped-bonnet
0-35psi, adjustable spring range, 5 micron filter
c/w Internal relief
Adj screw w/ closing cap
WGI ¼”npt 0-160psi dual scale, liquid filled, 2.5” pressure indicator
Heater:
CCI 24” x 24” WX Series cata-dyne explosion proof heater
12 Volt start w/ 30’ cables
11” W.C. Nat gas thermocouple & ASV375 valve
CSA approved
Fisher 912 regulator, grill, vent hood, temp control and accessories
Support Skid:
10’0” x 10’0” Structural steel skid
W6@15 Main rails and vessel supports
C5 Floor support
4 – Lift lugs
3/16” Checker plate floor area
2” Poly-urethane spray foam insulation under checker plate
Building:
10’0” x 10’0” x 10’0” H Shed style foam panel building
1.5” thick; 28Ga Polyurethane foam panels (R12); Galvalume (interior/exterior)
(1) 3’x7’ Foam panel door c/w panic hardware (Von Duprin – model 44TP) c/w locking cylinder
2’x2’ GPW, check-chain, door sweep, mohair weatherstripping & butt hinges
(2) 12”x12” stamped aluminum vents c/w manual sliders
Valves:
3 – Frontier 2”npt 2000#RP ball valve, cs body ss trim
2 – Frontier ¾”npt 2000# RP ball valve, cs body ss trim
4 – Frontier ½”npt 2000# RP ball valve, cs body ss trim
2 – MAS ½”npt 2000# RP ball valve, cs body ss trim
2 – WGI ½”npt MxF 10,000# needle valve
3 – WGI ¼”npt MxF 10,000# needle valve
1 – Plainsman cb-50 ½”npt FxF inline ball check valve

 

Add To Cart

New

East Central AB